DSG opnieuw inleren

Bij normaal rijden schakelt mijn DSG goed. Als de bak koud is voel je hem soms naar z'n 5 schakelen, maar meer niet. Nu kwam ik er laatst achter dat bij hoogtoeren schakelen (kick-down of S-stand) de bak soms aardig wil schokken bij het schakelen, vooral bij de 3e en 5e versnelling. Na dit een aantal keer herhaald te hebben, lijkt de bak alleen nog maar te schokken bij manual naar 3e versnelling schakelen bij z'n 4000-4500 toeren. Geen ramp. Nu kwam ik op internet berichten tegen over het opnieuw inleren van de DSG via VCDS en dat dit eventueel de souplesse kan verhogen. Sommige raden dit ook aan na tuning of in het algemeen om de zoveel tijd. Als dit echt de souplesse verhoogt, dan lijkt het mij het porberen waard. Ik ben een aantal methodes tegengekomen, maar volgens mij heb ik methode gevonden die op mijn DSG (Polo 6C 2015) van toepassing is:


Nu is mijn vraag aan jullie: zijn er mensen die ervaring hebben met het opnieuw inleren van de DSG? Heeft het effect gehad of niet? Hoe hebben jullie dit gedaan?

Ik ben benieuwd naar de reacties.
 
Volkswagen  Polo 6C  1.2 TSI 140pk 7DSG 
Ik ervaar hetzelfde met mijn DSG. Ik heb mijn DSG een stage 2 tuning gegeven, hiermee wordt de software van de DSG veranderd en dat verbeterd de rij ervaring. Dit is inderdaad het geval, de toerentallen worden gewijzigd naar een toerental waar de auto soepeler zal schakelen en daardoor soepeler optrekt.

MAAR, wanneer ik net als jij volgas optrek en onder vollast hoogtoerig opschakel heb ik nog steeds dat schokkerige. Ik vermoed dat dit bij onze DSG7 er niet uit te krijgen is. De DSG7 staat bekend als minst goede versnellingsbak van VW..

Mijn auto is ook al 2 keer bij de dealer geweest hiervoor waarbij ze 1 keer een herkalibratie hebben gedaan en dit heeft het ook niet opgelost.
 
instagram: @rline_polo_ || Volkswagen  Polo AW  1.0 TSI 115pk DSG-7 
  • Leuk
Waarderingen: Willykr
Kijk eerst of er een DSG update voor is. Dat helpt meer dan ff een herkalibratie.
Als het software nummer bij elke versie 1 ooghoogte dan zijn er zeker nog wat updates.

Screenshot_20200914-194304_OBDeleven.jpg

Morgen maar eens aan de dealer (Ames) vragen hoeveel het kost om de updates te laten doen. Ik zag dat er voor nogwel wat module een update is.

Verwacht daar vooral niet veel van. Na andere software gebeurt dat
Ben benieuwd wat het doet. Hopelijk wordt het iets beter. Dat zou al mooi zijn, anders jammer dan. Maar bedankt voor de waarschuwing.

Ik ervaar hetzelfde met mijn DSG. Ik heb mijn DSG een stage 2 tuning gegeven, hiermee wordt de software van de DSG veranderd en dat verbeterd de rij ervaring. Dit is inderdaad het geval, de toerentallen worden gewijzigd naar een toerental waar de auto soepeler zal schakelen en daardoor soepeler optrekt.

MAAR, wanneer ik net als jij volgas optrek en onder vollast hoogtoerig opschakel heb ik nog steeds dat schokkerige. Ik vermoed dat dit bij onze DSG7 er niet uit te krijgen is. De DSG7 staat bekend als minst goede versnellingsbak van VW..

Mijn auto is ook al 2 keer bij de dealer geweest hiervoor waarbij ze 1 keer een herkalibratie hebben gedaan en dit heeft het ook niet opgelost.

Ja jammer dat het er niet uit te krijgen is. Ach zo erg vindt ik het nou ook maar niet. Bij mijn vorige DSG (met verbrande koppeling) had ik ook allerlei schokken ook na de optimalisatie. Hij was wel erg sportief afgesteld (op mijn verzoek). Daar had ik wel spijt van. Normaal rijden ging haast niet meer.

Ben benieuwd wat een software update en kalibratie gaan doen.
 
Volkswagen  Polo 6C  1.2 TSI 140pk 7DSG 
  • Leuk
Waarderingen: Steve Up! TSI
Als de dealer het niet wilt updaten, dan kan een tuner het wel updaten. Anders kan ik het ook wel doen voor je.

Bedankt voor het aanbod! Ben benieuwd of de dealer er nog wat voor rekent en hoeveel (zal wel wat kosten). Mocht het niks worden met de dealer, dan laat ik het weten.

Wel bijzonder dat jij software updates kan doen, dacht altijd dat alleen dealers dat konden. Dat aan de hardware te komen is snap ik nog wel, maar de software lijkt mij lastiger.
 
Volkswagen  Polo 6C  1.2 TSI 140pk 7DSG 
Bedankt voor het aanbod! Ben benieuwd of de dealer er nog wat voor rekent en hoeveel (zal wel wat kosten). Mocht het niks worden met de dealer, dan laat ik het weten.

Wel bijzonder dat jij software updates kan doen, dacht altijd dat alleen dealers dat konden. Dat aan de hardware te komen is snap ik nog wel, maar de software lijkt mij lastiger.
Haha ik kan bijna net zoveel als de dealer. Op sommige gebieden zelfs meer :)
 
Audi  A3 8V Limousine Facelift  1.4tfsi COD 
Nog even een update. De laatste tijd vond ik de DSG al beter schakelen. Toch gekozen om de software te laten updaten onder het mom van een nieuwe versie is beter. Gisteren langs geweest bij @Rainesh voor de update. Ben zeer tevreden. Bak is gelijk opnieuw gekalibreerd en past zich opnieuw aan de rijgewoonte van de bestuurder aan. Ben dik tevreden de bak schakelt veel vloeiender. Echt een aanrader voor mensen die nog met een oude softwareversie rondrijden.
 
Volkswagen  Polo 6C  1.2 TSI 140pk 7DSG 
Ik weet niet hoeveel kilometer je er op heb staan,je zou een diagnose kunnen laten uitvoeren,mischien toch je kopling versleten,daar word je niet blij van,ik heb hem ook moeten laten vervangen bij 130.000,nu rijd hij weer als nieuw,heb gelijk de schakel momenten laten veranderen staat nu pas in zijn 7 bij 80 km,ik hoorde je over Ames daar zou ik hem zeker niet brengen,ik weet niet waar je woont en ik hoop voor je dat het met een update te verhelpen is,anders heb ik nog een adres voor je,Garage Fijneman bv Ploegstraat 50 Dordrecht,Leo is een recht voor zijn raap man,en eerlijk,werken samen met Digicar.
 
Volkswagen  Polo 6 r  1.2 tsi 105 pk 
Je kunt heel simpel testen of er sprake is van slijtage. Zet DSG in manual 4, geef op gegeven moment vol gas en let op de toerenteller. Gaat de naald met schokken omhoog, dan is het mis.
 
Volkswagen  Up! GTI KWv1 Milltek Road+ OZ HLT matt black wheels  1.0 tsi 140 pk/225 Nm (Vagtechniek) 
je kunt ook het aantal mm dat de koppeling moet 'bijstellen' uitlezen met bv vcds.

Let op: alle informatie is voor de 0AM DSG7 DQ200, niet voor de DSG6 in de AW GTI

Basic setting.png

nog wat tekst dat ik ergens had:
So I decided to make the same entry in my logbook so as not to look. Thanks to the driver whose link is at the bottom of the article.
Everything that will be described below applies only to the DSG-7 0AM DQ-200 gearbox with dry clutches, and is not applicable to the DSG-6 02E DQ-250 gearbox.
The conference on Yeti-Clube prompted the writing of material here: www.club-yeti.ru/forum/showthread.php?t=1870 The
material was collected bit by bit, including from there.
As you know, this gearbox uses double clutch, the inventor and manufacturer of which is the company LUK. It has long been known about design problems, this is a feature of dry friction clutches, as well as the absence of a torsional vibration damper on the 2nd clutch disc, which largely influenced the appearance of vibrations in 2nd gear. Nevertheless, despite the discomfort, practice has shown a rather high resistance to wear of the friction clutches, but everyone wants to know what is the current production of clutches, and how much they have to ride. This material is devoted to the analysis of the remainder and the quality of the clutch discs gearbox.
I must say right away that the main kinematic difference between a DSG7 and a manual gearbox is that in a manual gearbox there are two main clutch positions - on (pedal released) and off (pedal clamped). Middle positions are only at the moment of starting from a place, then the driver does not touch this pedal, except for the moments of switching. In the DSG7, the clutches are normally open and the mechatronic clamps the clutch in proportion to the moment to be transmitted, i.e. as if playing with release rods. The more we press the gas, the stronger the corresponding mechatronics rod comes out and clamps the friction clutch. Accordingly, there is an operating range of the stroke of the rods, and there are limit values. When the friction clutch thickness is extremely worn out, the stroke of the rods is no longer enough, and the disc begins to slip. Also, the disc may begin to slip earlier due to the loss of its properties from overheating or deformation of the friction material. A natural consequence of this will be overheating of the disks; for this, another evaluation criterion is important - the temperature map.
Thus, the assessment of the state and quality of adhesion is reduced to the assessment of the mechanical and temperature parameters of the work. To evaluate the first parameter, it is best to do this while traveling on a test machine with a laptop, in order to remove the parameters in dynamics, they will most clearly show the current state of the clutches.
The figure below shows the graphs of the limit values of the stroke of the rods, and the operating range. As the friction clutch wears out, the blue curve shifts to the right, and when it reaches the limit value, the clutch requires intervention to replace the clutch.



56HBxNf.png






Fig. 1.
For diagnostics, we will need a VAG-COM lace, or a Russian analogue of Vasya-Diagnost. We connect, go to Block 02 “Transmission Electronics” (02-Auto Trans), see the software version. The last 4 digits in the upper right field, in this case 2680. Do not forget, fresh software is one of the conditions for longer operation of the box, as it incorporates corrections and optimization of operating modes.



6GV9Liw.png






Fig. 2.
Next, click on the “Measurement Block” (Meas. Blocks - 08).
First, go to the measured groups of the 1st disk, 95, 96 and 97. Read the parameters. Data analysis consists in constructing a graph similar to Fig. 1, from which it will become clear how far the travel curve is from the limit value. However, this issue can be clarified even without plotting, it is enough to subtract from the limit value of the stroke of the rod (in this case 27.0 mm) the value of the current limit position of the rod at which the maximum torque is transmitted (in this case 21.3 mm). Total we get: 27.0-21.3 = 5.7 mm - the “power reserve” of the stroke, which is gradually “chosen” as the clutch wears out. In Fig. 1 it is called "Residual. power reserve".
We perform similar operations for the second disk in the measured groups 115, 116 and 117. Here we get 27.0 - 22.2 = 4.8 mm.
How “scary” are these millimeters? Is it good or not? In fact, the remnants of the moves themselves do not fully reflect the remnants of the clutch, they only indirectly talk about wear, but there is an unconditional dependence. The smaller the margin left to the limit value, the greater the wear if the clutch has been installed and configured correctly, and the number and thickness of the washers-spacers is determined correctly. After all, after replacing the clutch, you can see that the remainder is only 2 mm, this indicates that the clutch is not installed correctly. Typically, on a new clutch, the power reserve is between 5 and 6.5 mm when installed correctly.



akmru36.png






Fig. 3. Parameters for the 1st disk.

RrrHsg8.png






Fig. 4. Parameters for the 2nd disk.
It is much more important to determine the rate of adhesion wear to take these parameters regularly, say every 15,000 km (for maintenance) and compare the residuals and their rate of change. For example, if it was 6.0 mm, and after 15000 km it became 4.0, then this is worse than, say, 4.8 mm, and after 15000 it became 4.3. But here, not everything is smooth. The fact is that these current (which we measured) values are recorded in memory after the last trip, and how we drove, smoothly, or without hesitation, pressured the gas - will also leave an imprint on the measurement result.
For a complete picture, we need to ride and measure the parameters in dynamics. Ideally, find a flat desert road, preferably not slippery, so that you can enter the maximum torque transmission mode without slipping. It is better to do this together, one drives, the other takes parameters.
To measure parameters in dynamics, we need to go to group 91 and 111 (for the 1st and 2nd disc, respectively)



3hq831Q.png






Fig. 5. The current position of the rods.
Press the Graph button, adjust the scales convenient for display (I set 0 - 30 mm) and actually start moving. Both in D mode and in manual mode at the set speed (preferably 4-5-6) so that it does not slip. Consistently measure the driving dynamics on an odd and even clutch. As a result of the trip, the following schedules are obtained:



mXZswWN.png






Fig. 6. Movement in D. mode. Green - 1st disk, lime - 2nd disk.



4WEXkn7.png






Fig. 7. Movement in manual mode with different force pressing the gas pedal. Green - 1st disk, lime - 2nd disk.
The graphs show that the position of the rods is very far from the limit value (27.0 mm). The test car is a Skoda Octavia 1,8TSI with a practically new clutch, unfortunately the road conditions were not very dry, and the road was not the freest, we sometimes allowed wheel slippage, and this can be seen from the graph that the rod moves even to 20.0 mm they didn’t come very close, that is, no more than 200 Nm of torque was transmitted.
So, if at peak loads the graphs with a margin did not reach the upper bar, then everything is in order and mechanical testing can be considered complete. Now turn to the temperature conditions. The statistical picture for both disks is read in groups 99, 102 for the 1st disk and 119 and 122 for the 2nd.



Jxm1UBY.png






Fig. 8. Temperature map of the 1st clutch disc.



Fig. 9. Temperature map of the 2nd clutch disc.
From the pictures it can be seen that my clutch practically did not have critical operating modes, and most of the time it worked at temperatures below 150 degrees, and even more than 75% of the time below 100 degrees. This is confirmed by the following measured groups 98 and 118 for the 1st and 2nd discs, respectively:



Fig. 10. Disk parameters: Friction coefficient, disk deformation, and temperature extremes.
The friction coefficient ranges from 0.95 to 1.00 (although sometimes the sensor shows more than one, this is a feature of indirect measurement) and depends on the current temperature. If the coefficient of friction is much lower - an alarming symptom. Also, the deformation of the clutch discs - I do not have, it is also measured indirectly. The last column - the limit value of the temperature of the disks shows how the maximum temperature of the disk over the entire period of operation of the car. I also had about 225 degrees on the 2nd disk, but in the process of measuring to write this manual, I held the handbrake and turned on the reverse, and so I periodically released the brake and pressed the gas slightly until I saw that the values exceeded the previous maximum . Thus, I found out that it is possible to literally heat up and even overheat the clutch discs in just 2-3 minutes.
Further, in order to understand how the disks are heated in dynamics, we select measurements of the current temperature of the disks and construct graphs based on the readings of group 126:



Fig. 11. The temperature schedule of the clutch.
In order to achieve visible peaks of temperature increase during the switching process, I pressed the gas pedal harder. The numbers indicate the slopes of the graph, at what speeds the readings were taken. Yellow graph - disc 1, odd gears, Blue graph - disc 2, even gears. Conclusion - the stronger we press the gas, the stronger the discs are heated. If you start annealing, then overheating the disks is not a big problem. And now DSG chip tuning enthusiasts - think about whether it's worth it. With an increase in the temperature of the disks, the friction coefficient also decreases and the temperature deformation of the disks occurs, as well as the notorious smell of a singed disk, if this is done often, then an “avalanche” deterioration of the parameters will begin. True, DSG comes to the rescue here too, when the drives overheat, it simply disengages the clutch and gives an error that takes some time to cool the drives, the so-called overheating alert.
To assess the temperature dynamics, I rode for half a day with a laptop in the usual city mode, both on traffic jams and on free roads. I was surprised that if you drive quietly through moderate traffic jams (there were no others), then the temperature of the discs rarely goes above 100 degrees. If you run from a traffic light to a traffic light in the stream, then the average temperature is kept at 100-110 degrees. And if in the evening anneal on desert roads, then on average the temperature will be 140-150 degrees, in peaks reach 200 degrees. It seems that to raise the temperature for 200, you need to either drift or press on the gas with the handbrake held (which I did on the reverse test with the handbrake held). This is where the temperature ends.
Additional general parameters of the box can be found in groups 56, 57 and 58 - they show mechatronics errors. If all fields are 65535, then there were no mechatronic errors.



Fig. 12. The number of mechatronics errors (inverse reading), 65535 - no errors.
Well, the final measurement parameter is the number of adaptations, group 180 for the 1st disk, and group 200 for the 2nd.



Fig. 13. The number of mechatronics adaptations for the 1st and 2nd disc.
Typically, the number of adaptations of the second disk is three times the first. More precisely, the ratio A1 / A2 = 1/3 and should not exceed this value. If it is more than 0.33, this is an alarming symptom, indicates the non-stationary parameters of the disk, roughly speaking, the mechatronics does not find a place for correct operation and is constantly looking for it.

What conclusions can be drawn from all this?

The devil is not so terrible as he is painted. The physics of DSG7 is pretty simple and straightforward, if you understand it and adapt to its optimal performance, it will last a long time, if not, then how it goes. VAG engineers are struggling to ensure that this “how it happens” is as long as possible in time, realizing that a simple layman does not want to delve into (and he should not) the intricacies of this mechanism. However, the task of those who nevertheless tried to understand is to do it as competently as possible, and this can help the townsfolk to make their life happier.

Adapting the DSG-7 0AM box - is it needed? From my experience I can say that it is not needed. The box itself adapts to the changing disk settings. Forced adaptation can be carried out if there was a software update, a global reset, the presence of errors or box replacement, but I’ll say for sure that this is definitely not the point for which it is worth taking money. Keep in mind, do not pay money for something that does not help you if there really are problems, even if you were promised that the problem should go away, as an example, eliminate vibration in 2nd gear. The nature of vibrations is completely different! And after a while they will appear again. Therefore, diagnose the box correctly!

PS. This is not the final version of the manual, I will refresh it and supplement it as new interesting and useful facts are clarified. Feedback is welcome. I do not pretend to be true in the last resort, I tried to chew it as clearly as possible and make the evaluation of the parameters easy and affordable.
www.drive2.ru/l/384355/
 
  AdBlock gedetecteerd
Wij snappen dat advertenties op de website niet leuk zijn, echter het draaiend houden van de website is helaas niet gratis. Wij hebben jaarlijks kosten aan de software licenties en het draaiend houden van de server. Wij zouden het erg op prijs stellen als je de ad-blocker wilt uitschakelen voor onze community zodat het voor iedereen gratis toegankelijk blijft. Voor nog geen 50 cent per maand kun je ook je account upgraden als je geen reclame wilt zien!